A model for understanding thecity in terms ofeight characteristic “city types” is proposed. e most human cities consist ofadaptive city types that act in acongruent manner. Any city can be analyzed as a particular mixture ofthese eight types. Competing city types combine and interact in dierent ways, and users feel theresult as an essential quality oftheenvironment. Some types either add to, or cancel and destroy each other, whereas others can juxtapose without interacting. is eight-fold model ofcity types helps us to predict thesuccess or failure ofdistinct urban regions in promoting urban life. It also suggests how to repair declining or non-existent pedestrian activity, and how architectural projects could aect the city adversely or positively. One section ofthis paper is devoted to techniques for designing urban spaces that invite human engagement, and another to designing acampus.

In this work, the process of OCM carried out over Mn-Na₂WO₄/SiO₂ integrated with selective oxidation over Ag/support was investigated. the effect off feed gas composition and OCM bed temperature as well as the position of Ag/support bed and additional oxygen injection before this bed were investigated. At optimal OCM conditions for the Mn-Na₂WO₄/SiO₂ catalyst (CH₄/O₂ = 3.75; V_tot = 77 cm3/min; T = 780°C), the injection of additional 4 cm3/min ofoxygen into the bed of Ag/support (working at 250–300°C) leads to a preferential oxidation of CO to CO₂.

This paper presents results of a numerical analysis of the stability of a gabion retaining wall. The main objective of the paper is to identify how different methods of the modelling of gabion joints affect the stability of the structure.

This paper presents the results and the process of numerical analysis of a selected section of the concrete dam  in Roinów.  The calculations  were  carried  out for two  different variants: the  gravity section  and the buttress section. The effects of the geometry  on the temperature  distribution inside the section, and the effect of the temperature on displacements, were examined.
 

High chemical stability, resistance to changes in the pH, pressure and temperature meant that zirconium oxide is widely used in many fields. It is used in water treatment and waste water treatment processes, as
well as air purification. In this paper, selected methods  of nano-zirconia synthesis in liquid phase were characterized.  These methods  include,  among  others, the microemulsion  method.  Based on literature data,  the advantages and difficulties associated with the use of each method  are presented, in order to answer the question of which method of nanometric zirconium oxide synthesis in the liquid phase is the most  advantageous.  The authors  also  pointed  out some  directions of development  for the discussed methods, which relate to, among others, solvent change and the use of additives in the form of polymers.

In the article, the value of compressive stress defined according to the jlat jack method with a theoretical value of the stress was compared. Te test was performed in a laboratory using part of the 38 cm thick masonry wall according to the procedure described in the ASTM C1196 – 14a Standard. Significant correspondence between the obtained results confirms that this diagnostic method is useful in Polish conditions as well as it allows one to estimate approximately how accurate it is.
 

This paper presents a design for a decentralised intelligent network of five wet pit pumping   stations in a rural area. This enables the network to automatically respond to inflow conditions  divergent to the base flow and use the storage capacity of the system to prevent sewer overflows. First results for the base flow and a simulation of the network in EPANET are presented.
 

The paper describes the working conditions of hydraulic prop in particular issues related to their dynamics. On this basis, mathematical model was developed for given simplifying assumptions. The paper includes description of simulation model as well as an experimental verilication performed in HSW Stalowa Wola.
 

Micro-extrusion  is the  process  of obtaining  microtubes  with  either simple  or  complex   cross-sections which are used for the high-precision transport and protection of various of media. Through this process, it is possible to create tubing with interior diameters and wall thicknesses as small as 0.1 mm and 0.05 mm respectively.  Micro-extruded  tubing  such  as micro  catheters and peripheral  intravenous   cannulas  are employed  in microfluidics, paediatrics and micro-analytics.  This article presents the results of granulometric tests of micropellets produced by micro-extrusion with cold pelletizing and results of tensile strength tests of microrods  of different diameters. The trials were performed using a standard twin-screw extruder and low-density polyethylene.
 

This article compares  the results of a high cycle fatigue analysis obtained through the application of the two methods dedicated to analysis of response of the structure of the bi-modal type – the direct spectral method and the Fu-Cebon one. the compared parameter is the lifetime for an assumed material S–N  curve and stress spectrum defined in an article by Fu & Cebon.